• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. They don't get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will reduce costly repairs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and may even be fatal. It is crucial to take the time to make sure that you're doing everything you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace, and they typically fit into frames of the past easily. If you have double glazed window repairs near me-paned windows that are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this instance, you will need to source some plastic spacers to help the new pane to fit perfectly into the window frame.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards of glass fall onto the fabric and not on the floor, where they could be trampled under.

Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to stop water and drafts from entering the home until a professional is able to come out and repair the window. This also serves as an obstacle to stop criminals from getting into your home. If the distance between the door and the window is large, you might want to use a security screen that also has an opening. This will provide the best of both.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash window. Over time, they can develop a number of problems that include sagging. A sagging window can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to stop the issue from getting worse.

Repositioning the hinges can help fix a window that is sagging. You'll first need to open the windows to get at the frame. With an screwdriver, unscrew the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you've moved your hinges. If you are happy with the fit of the window, you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause them to lose tightness. If this happens, it's important to replace the seal as fast as you can to ensure that your uPVC windows are waterproof and draught-proof.

UPVC handles can also become loose. This is often caused by screws that have loosened over time, but it could be due to the handle mechanism wears out. Luckily, it's not difficult to repair a loose uPVC window handle yourself. You'll first need to close the window and do an experiment fitting. The joint at the corners of the sash should align with the joint on the casing. If it isn't then you can use a screwdriver or a wrench to loosen the handle and reverse the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and damp walls every time it rains it's crucial to take action. Windows that leak water do can not only cause destruction of your home's structure but also undermine your efforts to regulate the temperature within your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by anyone who is a DIYer with the skills. Depending on the severity of the issue is, old caulking may need to be removed. It is essential to keep in mind that when it comes to uPVC window repairs, do not be tempted to apply too much caulk' as this will only make the area more difficult to clean and can decrease the efficiency of your energy usage.

Make sure that the drainage holes do not have debris in them, and also ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you may need to think about replacing the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives under conditions of dampness and can spread quickly throughout the house.

It is also important to note that if the leakage is coming from between the glass of your double-glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sagging. Again this can easily be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and open with ease it could be hinges that are at fault. Any competent DIYer can replace the hinges in a matter of minutes.

Like all mechanical parts hinges are prone to be damaged over time. It's easy to replace a hinge on a window but it's much easier if someone else helps you to hold the frame.

Verify that the uPVC hinges open and close in the right direction. You can check this by checking for the arrows on each hinge, this indicates the direction in which the window should open.

The issue can be caused by opening the window improperly or due to a poor installation in the factory. This issue can be fixed by sending us a photograph on our website. We will be happy to give you advice.

Regular lubrication of the hinges is also necessary. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window operate and close more smoothly. It also helps prevent corrosion and reduce the possibility of sticking. This is recommended to be done at least once a year. WD40 and other solvent-based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different causes. The hinges may also become disaligned as a result of wear, which can cause a gap where the sash meets frame. If they are beyond repair, it may be necessary to get them re-aligned. Secondly the interlock, this is on the hinge side of the window and can also become misaligned, again it may be feasible to give them a good clean, but in some instances it could be necessary to have these replaced.

The next most common reason for draughts is window seals. They can become worn down or damaged over time and will allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, this will help in regulating indoor temperatures and again will lessen the risk of draughts.

Lastly, one of the most effective ways to cut down on drafts is to use an draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be put on the windowsill on top. They will help block out cold air and keep your home warm and cosy!

Your windows made of upvc will keep providing excellent insulation and security to your home with regular maintenance and repairs. It is crucial to realize that all windows have a lifespan and there may come a point where it is more economical to replace them than repair them. If you are having issues with your upvc windows, it is always recommended to seek assistance from a professional as soon as you can.