• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a doable job for most homeowners. If, however, the screw holes are damaged and aren't able to hold screws, you might need to put in wood glue and dowels before you can install the window hinge repairs.

Clean up any surface that has rust. This will help keep the dowels in place and provide a solid base for them to grip onto.

Take off the Hinges

Many standard door hinges can be removed, which makes it easier to move the door from one end of the frame to the other side or remove the entire door in the event of need. Anyone with a bit of patience can remove the hinges however, you must know what to do.

If the double glazing hinges are painted, you will need to remove the paint prior to attempting to remove the pins. You may scratch your door if don't remove the paint. Put the hinges in a stainless steel pot and fill it with water until the hinges are completely submerged. Allow the hinges to sit in the pan for about 30 minutes. The heat of the water will soften the paint making it easier to take off.

Once the pins are loosened, you can remove the hinges from the door and frame. It is possible to use a standard screwdriver, however you should use a magnetic screwdriver for this project. This type of screwdriver is designed to pick up screws made of metal and make the task go much faster.

Before you attempt to remove the window hinges replacement, it is a good idea to spray them with some grease. A simple lubricant will help the process to go more quickly and aid in the removal of the pins and screws. You can find this type of lubricant at most hardware and home improvement stores.

Keep in mind that the number of door hinges you'll need will vary depending on the door's type and its configurations. Heavy doors and solid-core doors will require more hinges while hollow-core doors with a lighter weight might only require two or three.

It is also important to understand the different types of hinges to determine which ones best suit your needs. Exterior hinges are designed to support the weight of a door, but interior hinges must be able to handle heavier loads.

Reattaching the Hinges

Over time the hinges on doors can become loose and start to hang crooked or sag. This can cause problems however, it's usually simple to solve. Retightening the screw will typically solve the problem. However when the screw holes have been stripped out, this can be more difficult. There is a trick to make the holes back in place using a wooden dowel.

Start by drilling the old hole using a drill bit close to the size of the new screw (normally 3/8"). Then use a wood glue as well as a wooden dowel to fill the hole. To ensure a snug fit, the dowel should be cut to the same length as the screw. Reinstall the screw and tighten it until you are satisfied with the degree of tightness. If the door has the tendency to be bowed the door, then add a second dowel to the gap and repeat the process. Be sure to close the door slowly so that you can verify the clearances at the perimeter after each adjustment.

You could also use a wood plug instead of the dowel. This will work equally well, but may take a bit longer to install. Simply whittle a chunk of wood to the appropriate size for a comfortable fit, then tap it into the hole. If you don't have an instrument for woodworking You can use toothpicks or matchsticks made of wood.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have reinstalled it. This will prevent the screw from rubbing against the edges of the doors as they are closed and opened. This will make it much easier to tighten the screws before installing hinges.

Once you have reinstalled the hinge, be sure to grease it with a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are excellent alternatives. You should apply a thin coat and give it about 15 minutes to fully reach the barrel of the hinge.

Refinishing the Hinges

If you're unsure whether to replace upvc window hinge hinges, you could try a few fixes. The first step is to check whether the screws that secure the hinge plate to the door and frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be careful not to tighten your screws so much that they begin to create gaps in the trim joints or, even more damagingly cause threads to be stripped.

If the issue is that the hinge plates are separating from the jamb and door and jamb, you can Fix door hinge them by gluing wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will provide a solid base for the screws and prevent the plates from shifting when you drive them into place. Let the glue dry before attaching the hinge.

The screws can also be smashed or gone. This issue can be resolved by replacing the screws. Use a drill bit that is similar to the size of the screw hole to prevent drilling into the jamb or hinge.

After you've reattached your hinge, close the door and look at the gap between the frame and the door. The gap should be about the thickness of a penny or less if an older door was not properly hung. This should not be a problem if hinges are properly installed.

If you find that the hinges are still loose, try putting the thicker shim of the hinge between the hinge plate and the mounting surface, to create an extra inch of space. You can also remove the hinge pin, then pound it down with a heavy hammer in order to tighten it, or install a new hinge. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and help keep them in position. Lubricating your hinges periodically will stop them from becoming stiff and squeaky and also extend their lifespan.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. Without regular cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and accumulate over time. The hinge will get stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection will preserve the integrity and functionality of hinges on doors.

Examine the hinges for signs of corrosion. If the rust is so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you can save the hinges, clean any loose rust by using wire brush and steel wool. Apply a commercial rust-removing product or homemade solution like lemon juice to the hinge. Let the rust removal solution be on the hinge for a few minutes to dissolve and penetrate any remaining rust.

Retightening screws can help restore hinge functionality in the event that you don't want to spend money or time on repairing hinges. It may be necessary, however, to add dowel or shim made of wood to the hinge in the event that the screws have been degraded. Dowels made of wood come in round rods of varying lengths and sizes. They are available at home improvement stores as well as woodworking supply and craft shops, or on the internet.

A shim can be made of metal or plastic, depending on the type of hinge you have. To make a dowel, cut an unfinished dowel into the desired length. Then, dip a dowel into the adhesive of a carpenter and place it in the hole. The glue will hold the dowel securely in the desired position.

Before you start cleaning the hinges, lay down a cloth or paper towel to protect flooring and other surfaces from accidental spills and drips. After the area has been secured then clean the hinges using an absorbent sponge or a soft cloth coated with a mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. You can make use of a small or toothbrush brush to reach difficult-to-reach places in crevices or tight areas.